Do you have blinds that need fixing? If so, you are in the right place. Here you will find 12 steps to improve your blinds that can be completed in about an hour or two with standard household tools. If your window treatments have not been working for months, you can use this repair guide before calling someone over to fix them. So, without further ado, here they are: (Credit Information: https://dpinteriors.net/fix-my-blinds)
Step One: Locate the Broken Cord
The first step is to locate the broken cord. You can identify the cable while looking for a broken string or wire on the blinds. If you cannot find it, try shaking the blinds and see if anything falls out.
Step Two: Remove the Blinds
Once you have found the break in the cord, it is time to remove the blinds. You can do it by pulling them
down off of the window and unplugging them from where they are hanging. Be careful not to damage them while taking them down.
Step Three: Cut Off The Broken Cord
Now that you have removed the blinds, it is time to cut off the broken cord. Use scissors or a knife to do this, and make sure to leave enough thread on each side as you proceed with the “fix my blinds” process.
Step Four: Check The Blinds for Rust or Damage
The next step is to check the blinds themselves for any rust or damage the broken wire may have caused. If you see a lot of rust, it will be necessary to sand down and repaint these parts before continuing with your fix. Make sure not to paint over the new replacement cord because this can cause problems later on if left unpainted.
Step Five: Tie One End of New Cord Onto Existing String/Wire
Things start getting technical as far as how much experience working with cords people might have had in their lifetime usually determines they are non-disabled enough to execute your “fix my blinds” steps carefully. The next step is to tie one end of the new cord onto the existing string or wire. You can do this by making a loop with the cable and using pliers to twist it around the string/wire tightly.
Step Six: Feed New Cord up Through Hollow Tube on Blinds
Now that you have tied one end of the new cord, it is time to feed it through the hollow tube on the blinds. Consider providing one end through a small opening at the top while holding on to the other end so that it does not pull back through.
Step Seven: Pull New Cord all the way Through until Both Ends Are Even
Once you have fed your new cord through the hollow tube, it is time to pull it through until both ends are even. It might take a little bit of maneuvering and patience, but you should be able to get there with enough effort.
Step Eight: Tie Second End onto Cord That Is Already Tied Onto String/Wire
Now that you have pulled one end of the cord entirely through, tie the other end onto one already tied into string or wire from earlier in this “ fix my blinds” guide. Make another loop using pliers and twist tightly around the existing knot before hanging blinds back up again on the window where they came down from initially.
Step Nine: Cut Off Excess Cord at Both Ends
Now that you have tied both ends of the cord onto the existing string or wire, it is time to cut off excess cord at both ends. Use scissors for precise cuts and maintain even cord length.
Step Ten: Hang Blinds Back up on Window Where They Came Down From
Once your “ fix my blinds” mission has been accomplished, all that remains for you to do is hang them back up on the window where they came down originally. Make sure everything looks evenly distributed before doing so because this step might require some maneuvering depending on how long your new piece of replacement cord was compared to the old one.
Step Eleven: Enjoy Your Newly Fixed Blinds!
Finally, once the hanging process has been completed, all that remains for you to do is enjoy your newly fixed blinds! They should work just as they did before your “fix my blinds” efforts and hopefully last long without needing further attention.
Step Twelve: Dispose of Old Cord Properly
Last but not least, make sure to dispose of old cord properly to avoid injuries or accidents later on with kids, pets, or anyone else who may come into contact with it. There are usually trash receptacles designated explicitly for this kind of thing near most fix-it shops where people can bring broken appliances if needed. Just be careful about doing so because there might still be live electricity running through parts even though they seem disconnected.
Conclusion
While fixing your blinds, you likely made a mess in the process. Ensure to clean up any spilled paint or tools so that everything is back in its proper place and no accidents are waiting to happen. The “fix my blinds” guide assumes some basic level of knowledge when working with cords, and if someone does not feel comfortable completing the steps outlined, they should reach out for professional help instead. Hopefully, this was not the case for most people who decided to take up the “ fix my blinds” challenge.
Fixing your blinds is a relatively straightforward process that should not take more than half an hour or so to complete from start to finish. With these 12 simple steps, you should be able to eliminate any “ fix my blinds” issues without too much trouble and have them look as good as new in no time at all!
