Why is my Rockspace extender AC2100 setup network unstable?

Such problems occur due to the local environmental factors in your surroundings. You may also face this issue if your internet connection is not stable. If your internet connection is not stable, contact your internet service provider. If the Ethernet cable you have attached to your range extender, modem, range extender, and computer is not of good quality, replace it on a priority basis.

Resolution about re.rockspace.local: –

• Locate your wireless clients at a reasonable distance to the range extender.
• If you place your wireless clients far away from the range extender, you will receive weaker wireless signals.
• Reduce the number of wireless clients operating with the range extender.
• If you use more devices with a wireless network, you will receive less bandwidth for each device.
• Disconnect some devices to get better Wi-Fi coverage.
• You can have a test by adding one device at a time to your rockspace_ext wireless network to check for the maximum number of required devices.
• All the available wireless devices in your house try to send data over the air.
• You should decline interference from other wireless equipment.
• Try to change some wireless settings in your Rockspace AC2100 extender.
• You should log into the wireless settings. And then, click on wireless settings below the setup menu to change the wireless channels in your network.
• It is also essential to check the wireless region or the country, which should be correct.

How Do I reset my Rockspace extender AC2100 setup device?

To reset your Rockspace extender, follow the guide in the below section;

• Turn on your Rockspace AC2100 extender. Connect the power line adapter to the power port at the rear of the extender and press the power button.
• If you see the range extender LED is solid white, then the range extender is turned on and is ready to use.
• Locate a small reset button at the back or on either side of your Rockspace Wi-Fi extender.
• Take a pointed object to press and hold the button as the reset button is inside the outer panel of your range extender for some security purpose.
• The reset button is required to be pressed by you for at least ten seconds and then the release button.
• Your Rockspace extender will reboot automatically. The device has been reset to its factory default settings and is ready to login back to its web interface.
• To login again to your Rockspace extender when it is set to its factory default settings, use admin as the default login username and password.

Why does the My Rockspace ap.setup page not work?

If you change the default username and password of your Rockspace AC2100range extender, then while logging in to the https://ap.setup page, your default password will not work. You have to use the configured password by you. If you do not remember the customized password, reset the range extender. If you have enabled the password recovery option, you can recover your password using the password recovery option. You can also implement the reset process when you forget your rockspace_ext login password.

Boost the ap.setup Wi-Fi signals of your Rockspace AC2100 extender

If you feel like your Rockspace WIFI signal is getting sluggish, there are a lot of tools you can use to test the wireless speed of your Wi-Fi Network. Slow browsing, crawling networks, inability to stream, wireless dead zones, dropping WIFI signals are some of the most critical problems in the world. Here, we provide you with some tricks to troubleshoot your network speed problems.

1. Before you blame your WIFI, make sure the internet is working as it should.
2. Find an Ethernet cable to plug your computer directly into the modem as well as the computer.
3. You need to run a speed test to see if your internet speed matches the speed on your Internet bill.
4. You can call your internet service provider to replace your modem if it creates problems.
5. Update the firmware of your range extender using the http://ap.setup web address or 192.168.1.1 address directly through the browser.
6. Update the firmware of your extender regularly whenever you find an update.
7. Relay only on the firmware update released by Rockspace.
8. All home WIFI range extenders cannot distribute the WIFI signals equally.
9. Where you place your WIFI range extender affects your WIFI coverage.
10. Place your range extender in the central location of your house.

Never keep your range extender behind an object that hides the signal.  Try to place the range extender in an open area, like on a table or a shelf. Keep the range extender far away from heavy-duty appliances or electronics, such as microwave, cordless phone, electric tandoor, heater, etc. If your range extender has some external antennas, orient them vertically to spread more WIFI signals eating dead zones.

Conclusion

When you proceed towards the setup process to access the Rockspace extender from a web browser of your choice, a login window will quickly appear on your computer screen. You will see the login window on the computer to which you have connected your Rockspace Wi-Fi extender. On the off chance, if your device does not connect to the Wi-Fi range extender, then the web browser will not access the Rockspace wifi login page. And then, you will get instructions to connect your device to the Rockspace Wi-Fi extender’s network to access the extender login web page.