How To Install Artificial Grass Step By Step In Dubai
Artificial grass, sometimes referred to as lawn, AstroTurf, or anything else you want to name it is sometimes difficult to install. Therefore, we advise hiring a professional to do it for you. However, if you are asking, “How can I put artificial grass?” while you look about, you should use this instruction.
Step 1: Set up the environment and resources
Visually inspect the area where the artificial turf will go and the surroundings. Make preparations in advance to make installation easier. The location where you’ll be working should be tidy. Select the necessary tools as well. After that, you must make a little clearing so that you may reach the area where you’ll work. Start using the hose to remove the dirt from where you will be installing the artificial grass. Once you have removed all the dust and debris, use a broom to sweep up any loose bits of dirt. It’s also essential for potential future usage.
Step 2: Excavation
For excavating in confined spaces, hand tools will be needed. After cleaning up the area with a lawn trimmer, you may eliminate any roots there.
Step 3: Define the perimeter
The moment has come to make any necessary alterations to the site’s irrigation, drainage, or other systems. Any electric, gas, irrigation, or telephone installation should be removed as soon as possible.
Step 4: Place a weed block fabric
The non-woven fabric, also known as a weed block, strengthens the structure’s structural integrity. The construction becomes more durable and stable as a result. The ideal option for protecting the installation from mice or pests and chewing roots is a weed block cloth that is 2 to 6 millimeters in thickness. There are several different weed block materials available.
Step 5: Base Installation
Start at the rear of the room to get the best results. Add 7.5–10 cm (3–4 inches) of compacted debris and smaller rocks that are 1.5–2 centimeters (0.6–0.8 inches). Layers of the material should be spread out horizontally, and heavy weights should not be placed on the ground before the material has been compacted.
Step 6: Compacting the base
Sharp edges, flat surfaces, and smoothness are required for the base. To quickly condense the foundation, you’ll need to push with a water-soaked roller. There should be no pebbles or other rubbish around the margins. You’ll need to make a few cuts into the base to dry it out before you can work on the next layer.
For a heavier, more solid foundation, you’ll need to gradually build up layers of stone and mortar in the same manner. Fill the foundation with a thin layer of mortar until it is level with the surrounding ground. Use a trowel to smooth out any rough edges. Fill in any hollow places where stones are missing by inserting another stone into them and smoothing over it with your hands or a trowel.
Fill in the spaces around the rocks with mortar, making sure not to let any mortar get on top or lodge between them. You may need to use a trowel or your fingers at the joints where two stones meet to ensure they are well and truly sealed together. Please leave it to cure for a few days before you move on to the next stage.
Step 7: Measuring, installing and setting the new artificial grass
Make sure your installation’s design is precise and understandable. Verify the installation surface and take several measurements. On a level area, roll out the artificial turf. Leave the grass flat on the ground for a few hours if you see any creases or wrinkles. The most significant piece of grass you’ll need is measured and cut.
Trim any edging on the grass blade. Reroll the synthetic turf and keep it for installation. You’ll need a level area, scissors, a measuring tape, a ruler, and a sharp knife. Trim any excess grass from the actual piece of turf you’re going to use.
Place a few rolls of the grass on a level area and verify that it’s symmetrical and about 3 to 4 inches thick. Trim any extra grass from the artificial turf (around 1-2 inches) and then make a mark for cutting. Use a sharp knife and cut about 1/4 inch below the line you made, ensuring you don’t cut through the artificial turf. Remove any exposed grass from the piece of turf that you’re using.
Step 8: Spread the grass out and tidy up the margins
To prevent displacing the grass:
- Walk gently on it.
- Use 8 to 13 cm long nails or staples to secure the edges (3 to 5 inches).
- Ensure that the cutter blades produce incredibly accurate, clean cuts.
A space of 0.6 to 0.7 cm (14 inches) should be left between the fake grass and other objects, such as walls or sidewalks.
Step 9: Secure the edges and tidy up the surface
By securing the edge of the fake grass with 12 cm (5 inches) nails, you can prevent the materials from changing form as a result of weather changes. The perimeter is best secured by anchoring it to a flexible material, such as a bender board. After that, pick up any fiber fragments that may have dropped during installation.
Now that the fake grass has been brushed to return the fiber to its upright position, you may sweep the area and remove any particles. Cleaning before and after installation may also be required. To keep the look of your fake grass neat, use a garden rake to remove dirt and debris. Take special care to remove all small rocks, animal droppings, or pest eggs that may have fallen onto the surface.
Step 10: Fill in the gaps and complete
You will require a drop spreader, hand tools, and filler materials. The drop spreader is crucial to ensure that the infill is deposited correctly. When dropping the infill, be cautious about moving gently and avoiding overlapping the rows. Sweep and remove the fiber blades with a carpet rake or a solid synthetic push broom. Additionally, it will assist in evenly and thoroughly distributing the infill material throughout the artificial grass—hand-finish everything that needs finishing, especially the edges.
You can make your fake grass installation appear excellent by following these instructions.