Due to busy schedules, it is often difficult to find the time to clean every corner of your home. Professionals will find vacuum cleaners a blessing as they save time and eliminate germs from home. But there are some minor problems with vacuum cleaner which we need to solve at time.
Technological advancement has enabled vacuum cleaners to be equipped with HEPA filters, which trap and capture contaminants from the surface.
There may be times when your vacuum cleaner stops working. These are common steps that you can use to repair or test your vacuum cleaner in such an instance. Continue reading.
1. Low Suction Force
A common problem that many people have is reduced suction. To test for decreased suction, empty the dust canister.
Next, check the filter, brush roll, and hose. If you find obstructions, remove them.
It is time to inspect the belt to see if all of these parts are free and unobstructed.
If the brush roll spins slowly or stops spinning, it could be an issue with the vacuum belt. You can replace the belts easily, and they aren’t very costly. Shark rocket ultra light hv30 vacuum cleaner is one of the best vacuum cleaner which consists all these attachments with guarantee.
2. Excessive Noise
Vacuum cleaners are quiet enough to be used for their convenience. If your vacuum cleaner makes a lot of noise, it could be due to a blockage, air leaks or problems with the fan or motor.
The vacuum cleaner will make much more noise if the belt is not attached. The motor may have a problem if the hose or belt is obstructed.
Before vacuum cleaners stop working, motors can become very loud.
3. Burning Smell
A burning smell is another common problem many people have with their vacuum cleaners. The belt may need to be replaced if you experience a burning odour when vacuuming.
You can only fix the problem by replacing the belt on your vacuum cleaner.
4. Hot Smoke or Hot Air
The vacuum cleaner can overheat, blowing out hair and smoke. If this happens, you should stop vacuuming immediately.
Do not attempt DIY repairs to the vacuum cleaner. Instead, replace the motor.
5. Blowing Dusty Air
This is because the vacuum cleaner’s canister is complete, and there isn’t enough space for the collected dust. To avoid this problems with vacuum cleaner, empty the vacuum cleaner’s canister.
You should change the vacuum cleaner’s filter if that doesn’t solve the problem. Vacuum cleaners are equipped with washable filters that reduce the hassle.
6. Bag Replacement Costs
It can be costly to replace bags. This problem can be avoided by using a water-powered vacuum, which doesn’t require expensive and messy filters.
If you don’t want to use a vacuum that uses bags to filter dirt and dust, then shop online at wholesale dealers for bulk deals.
This will ensure you don’t run out of bags whenever you need them.
7. Do Not Continue to Spin
Again, vacuum cleaner belts are responsible for the lack of spinning. The cleaner brush won’t spin if the belts are damage.
Check the drive and cogged belts to ensure they are in good condition. You have to replace them if any of the item is damage.
You may also find that your brush roll is jammed. Hence, you can also remove the brush roll from your cleaner and clean it before putting it back. Replace the brush roll assembly if it is not continue spin.
8. A Broken Belt
You can not repair vacuum belt. However, if it is broken, you can have it replaced by an expert. The belt that moves the roller brush is located at the bottom.
The cost to replace the belt will be between Rs 200 and 500. You only need a screwdriver to move the roller brush to put it on.
If you’re not confident doing the job yourself, we recommend hiring an expert. You should also not use the cleaner until you have changed the belt. Otherwise, the motor could fail.
9. Vacuum Cleaners Aren’t Sucking.
Do you find that your vacuum cleaner doesn’t pick up dirt correctly? You can easily fix this problem. These tips will help you solve the problem.
10. Full Dust Canister
Like bagged vacuum cleaners, a full canister of dust can cause problems with the suction. It is simple to empty the canister and get rid of the dust.
11. Dirty Filters
Suction loss due to the dirt or block filters. To clean the filters, use a mixture of baking soda and water. If this fails to work, you can replace the filters.
12. Blockages
Blockages in the vacuum’s tubing can cause loss of suction. Turn off the vacuum and unplug it. Also, make sure that the brush roll is clean. Damage brush rolls should be replace as soon as possible.
13. Air Flow Gaps
Your vacuum cleaner’s suction can be significantly reduced if there are holes or tears in the hose. The hose might need to be replaced if this happens. You should ensure that the connection between the hose & the base unit is tightened when uprights are used.
14. It Is Not Operating
Check if cleaner plugged correctly into the switchboard if it won’t turn on at all. This will ensure that the vacuum cleaner is receiving power. The electronic control board (PCB) may have burned out if the appliance is correctly plugged in.
In this situation, you have to change the PCB. There is also a chance that the drive motor has broken down or the thermal fuse has stopped working, switching off the power to the engine.
Typically, this occurs when an overheated motor burns out. You could try unplugging the vacuum cleaner from the circuit board and manually starting the motor shaft to look for any obstructions.
15. Full Bag
Check that the bag is incomplete if your vacuum cleaner stops sucking which is one of the problems with vacuum cleaner. You can simply replace the bag if everything is fine.
Last Few Words
Regular vacuum cleaner use can cause vacuum cleaners to stop working. You don’t have to take your vacuum cleaner to the service center.
You can try DIY methods to resolve minor problems with vacuum cleaner. So, you should have your vacuum cleaner’s motor repair by a professional if it is damage or not working properly.
For more blogs click, Dewarticles.
